Auto Repair Service

Free repair service information and advice.

How You Know You Need Timing Belt Kits Replacement?

Timing belt complications usually occur without warning. There are no signs of obvious impending damage like an abnormal noise or leaks that could help alert you. Moreover, if your car suddenly dies during its run and refuses to restart, it is most likely that your timing belt is damaged and a timing belt replacement is needed.

How The Came Belt Work ?

Most car owners enjoy the benefit of having a car. The only downfall for such is the responsibility of maintenance in order to make it last for a long time. The car’s belt is among the most essential parts of the car as it works as a linkage between the crankshaft and camshaft. It controls the opening and closing of the valves located in the engine of the car. Naturally, if the belt gets damaged, the car will fail to run smoothly and safely.

Keeping the timed motion of a car is important. Failing to do so will result to a collision between other car parts such as the valves, cylinder head, cylinder walls and pistons. The belt, then, was made to prevent such incident from happening. The belt syncs the mechanism of the engine every time the car is in motion. It rests on two crankshaft pulleys and each of these contain a timing mark. It is important that these marks are arranged according to the timing specifications of the car. The pulleys are then toothed to prevent the belt from slipping off or sliding around the pulleys. These are all commonly preserved movements that help in the successful running of the car.

Because the belt is made from rubber, it is prone to stretching and breaking due to too much heat. As heat penetrates to the belt, it stretches and deteriorates causing the teeth of the belt to wear out. If there are no teeth to secure the belt, a collision of car parts is made possible. In order to prevent this from happening, a regular check-up or inspection must be done by a certified mechanic. Prevention is better than the cure as this would lessen the cost of car repair and maintenance.

When You Need Timing Belt Replacement?

Furthermore, preventing the belt from breaking can’t be done, a replacement remains as the only solution. It is recommended that the car’s timing belt is replaced every 50,000 to 70,000 miles. This is, however, dependent on the car’s replacement intervals for timing belts. This auto repair service usually costs between $250 and $750. Your expenses will vary according to the condition of the belt’s damage.

How To Save Money Replacing Timing Belt ?

To save on costs, most car owners resort to replacing the belt on their own. Although it is a difficult task, it is not impossible to do. Experience and knowledge are, nevertheless, essential to have a successful replacement. It should be remembered that once the replacement is done incorrectly, your engine will not run. To avoid this, asking advice and recommendations from certified mechanics is a good measure. Researching is also logical to ensure more understanding regarding the replacement of timing belts.

Fouzis Service Centre does the finest service in timing belt replacement in Georgetown Germiston JHB that will keep your car in good condition. Take advantage of their certified mechanics that will do the replacement accurately.

I, Fouzi thank you for subscribing and visiting my website. My Car Symptoms, is my new e-book subscribe now . The part one ( How You Diagnose Your Car Problem To Save Money )  is Free for you  limited edition. If your car is in need for timing belt kits replacemeny contact me at Fouzis Service Centre for free quotation. I have special on timing belt repacement, 10% discount. Visit this auto parts store for timing belt kits prices  click here.

Advertisements

21/12/2011 Posted by | Uncategorized | , , , , , , , | Comments Off on How You Know You Need Timing Belt Kits Replacement?

When To ChangeTiming Belt

  

When To Change Your Car Timing Belt

Though many car owners and drivers are unaware regarding what the timing belt does, it is essential to the efficient operation of your engine. If  the timing belt breaks or slips from its place, your engine will stop working. It can even sustain heavy damage, bend valves, break rockers,  break your cam shaft and even damage your car engine pistons.The timing belt failure can cost you more money if you replace it in time.

Getting a timing belt replacement service done on your car as soon as possible is very important and you must take it seriously. You need not worry too much because there are certain very noticeable symptoms that will tell you that you need to get this kind of service done for your car. One of the best ways for you to determine that your car needs a timing belt replacement is by opening up your hood so that you can take a look at that part of your car’s engine closely may you can see cricked on the side of each teeth timing belt.

The following symptoms you going to learn are different types of symptoms that you need to look out for so that you’ll know whether or not you already need a timing belt change.

Excessive Exhaust Emission

Problems with a car’s timing belt will cause its engine to function improperly by loosing power, and will lead to excessive emission of smoke from the exhaust. This happens when the timing belt is no longer in sync with the closing of the exhaust valve. This can cause unused gases to be released at the car’s exhaust.

Difficult Starting Of The Vehicle

If you experience problems starting your car, your timing belt may not be functioning well. This problem can be caused by other reasons but if you experience this on a regular basis, then you need to get your timing belt checked.

Overheating And Leaking Engine

Very high temperatures in the engine or hot weather conditions can cause damage to the timing belts because they’re only made out of rubber. When damage happens to them, the engine can’t work in sync and overheating can happen which can be followed by leakage.

Sudden Changes In Engine Noise

If you notice unusual engine noise while you’re driving your car, this can be a probable symptom that you have timing belt problems and you need to get a replacement.

How A Replacement Is Done And The Cost To Do It

Below are the steps done when a belt replacement is done. Take note that this process is something that’s not good to do on your own. Getting professionals to do this for you is highly advisable. If you are worry about the cost of timing belt replacement can range between $250 and $750. These prices vary considerably on the make and model of your car as well as the labor price of the mechanic. To inhibit sticker shock, it’s most important to discuss cost during first consultation with your mechanic. A qualified, skilled, experienced, and highly regarded mechanic can provide you with quote and time frame depending on the make of your car.

The timing belt replacement is different from car to car and depend of cars make. I am going to give you example of timing belt replacement because I don’t know what make of cars are you driving.

1. Allow the car to cool down to normal temperature. Disconnect your battery.
2. Detach all of the parts that are going to prevent you from removing the old timing belt.
3. Get a spanner and place the mark on the crankshaft to the zero timing scale mark on your car’s engine block or remove the spark plug from the cylinder number one.Turn the engine full turn twice, place screw driver on the spark plug fitting tel you feel the piston number one is up. You should also see the mark on the camshaft poly is placed at 12 o’clock. If you don’t see any mark, remove the camshaft tapet cover. On the come shaft you need to rock number four cylinder and number one should be firing.
4. Loose the bolts that is holding the tension bearing . Look at the seals of the crankshaft and camshaft, tension bearings. If any of these parts are damaged, replace them so that the new timing belt won’t fail within a short span of time.
5. Remove the old timing belt and install the new one. Adjust and tension the timing belt according to the specifications provided by the manufacturer. Fit a new tapet cover gasket  and recheck the timing marks or turn the engine from the crankshat poly with spanner if the engine come to certain point and is not turning that mean your timing is not alright. You need to start the operation from scratch. Do not turn the engine turning the ignition key.
6. Place back all of the parts that you detached earlier including your car’s battery.
7. Start your engine and observe if the problems that your encountered before the replacement was done are still present.

If your car already needs a Timing belt replacement in Georgetown Germiston go directly to the Fouzis Service Centre shop. They provide top quality auto repair services for reasonable prices.

24/11/2011 Posted by | Uncategorized | , , , , , , | Comments Off on When To ChangeTiming Belt

Car Engine Repaired Or Replaced?

                          

Car Engine Repaired Or Replaced?

Having to replace an air pump is inconvenient, but tolerable. Replacing a muffler or alternator is more costly and thus, more frustrating. But it’s still bearable. Your car’s engine, on the other hand, is among the few assemblies (your transmission is the other one) where a failure can crush your budget.

Your engine will not last forever, of course. Depending on how hard you drive it and the number of miles you put on it, you can expect it to last between 100,000 miles and twice that amount. If you keep your vehicle long enough, it will eventually develop major problems.

Below, we’ll explore the decision to fix the assembly versus having it replaced. We’ll explain why uncovering the root causes of a given problem is a critical piece to making this decision. Lastly, we’ll describe the key differences between a brand new engine and a remanufactured unit.

Deciding Whether To Repair The Assembly

Suppose your vehicle is eight or nine years old and you’ve driven it extremely hard over those years. As a result, your engine has finally failed. The first question to ask is whether you should keep your car, or retire it and buy a new one. A lot depends on its age, value, and overall condition.

For example, if your car has a market value of $2,500, spending over $1,000 to have your engine repaired (or replaced) may make little sense. But if your vehicle has retained its value and other major components (e.g. transmission) remain in good shape, spending the money might be worthwhile.

Let’s suppose you have decided to keep your car. Now, the question becomes whether you should have the failing engine repaired or replaced. Your decision will largely hinge on its condition and the number of miles on it.

For example, if the assembly has 130,000 miles, a history of valve or piston problems, and a chronic misfire, repairing it will be costly. The mechanic might need to perform extensive work on the cylinders. He may need to align the engine block and replace the valves.

Also, with an overhaul, the entire assembly must be dismantled. The individual pieces are disassembled, so the mechanic can check for blemishes, fissures, or other structural problems. The components that are in good condition are then cleaned. The ones that are in poor condition are replaced. Once the parts have either been cleaned or replaced, the assembly is put back together.

This is painstaking work. An engine overhaul requires an enormous amount of time and effort. This is the reason a lot of mechanics will strongly suggest having the engine replaced.

Differences Between New And Remanufactured Engines

You can buy a used assembly from a junkyard, but doing so may be dangerous. There’s no way to be certain whether there are problems hidden from view, especially with engines that have a lot of miles. Even if you find a used assembly with low miles and a limited warranty, it will usually be a less-than-ideal option. The price will be consistent with a remanufactured unit, which will have been brought up to OEM standards. At that point, you’re better off investing in the latter.

A new engine is exactly how it sounds. Every individual piece is new. The valves, pistons, engine block, connecting rods, and other parts have never been used.

A remanufactured unit is nearly as good (and far less expensive). Remans are used assemblies that have been dismantled, closely examined, and carefully cleaned. Most of the pieces that wear over time (e.g. timing belt, gaskets, etc.) are replaced. Then, the assembly is rebuilt and tested to ensure it meets OEM standards.

Which option is best? If your budget is limited, a remanufactured engine that has been brought up to OEM specifications is an ideal solution. It will get your car back on the road without the high cost associated with a new assembly.

When looking for used auto parts and used engines consider the leader in parts, Click here and get BIG discounts plus FREE SHIPPING on auto parts and accessories at Auto Parts Warehouse.

I , Fouzi thank you for subscribe for more information , news letters , and Quote. Any problems about your car repairs  just subscribe for free, I will help you.

17/08/2011 Posted by | Uncategorized | , , , , , , , , , | Comments Off on Car Engine Repaired Or Replaced?

Car Repairs Estimates

                             FOUZIS SERVICE CENTRE

                  CAR REPAIRS ESTIMATES 


”  EVERYONE LOOKING TO SAVE MONEY ”

I hear this all time “why does it cost me so much to repair my car?” The answer I am giving you. You not looking or you can’t find an honest mechanic.What i am giving you now is the best prices , the best service, and honesty. The prices going to be send to you that what you going to pay , if you use my services. This is not a  flyer you pick up at the robot.Because we all know when we pick-up our cars from mechanic. The price we pay is normally double to what the flyer promised.         

Saving Money on Costly Engine Repair

Engine repair for your vehicle is news no one likes to hear. It can only mean 1 result, money spent on your car just to keep it running. Replacing the engine is usually the most expensive mechanical repair that is performed on a vehicle. People have to replace used engines for several different reasons. Most of the time failure is due to lack of maintenance. Issues that happen from not keeping your car are many. Dirty oil is always a problem for engines. When the oil is not changed on a regular basis sludge builds up. Most people do not realize engines have very small oil journals that need to stay clear so all areas of the engine stay lubricated. You can have just 1 of these areas get enough build up to restrict flow to a small area of the engine and the will in turn cause total failure of the engine.

The timing belt is a very inexpensive item that is over looked so much in today’s cars. Not because of the cost of the part but the repair itself is the issue. Your owner’s manual will have a recommended time when the timing belt needs replacing. To replace a timing belt means the front of the engine including all the belt driven accessories must be removed to replace the belt. The bigger problem is if the belt is not replaced when it should be. The timing belt is under a tremendous load and when it breaks, the engine becomes non-repairable. Most engines today are interference engine by design. That means if the timing is off, the valves will hit the pistons and major damage occurs. The timing belt goes around the crankshaft and up to the cam shaft. This is how the valves open to let fuel in and close for combustion, the exhaust valves open to let out the spent fuel. When the valves open they push down into the cylinder where the piston is moving up and down. The piston is on the down stroke when the intake valve opens and comes back to the top as the valve closes and the gas explodes. That pushed the piston back down and the exhaust valve opens to let the exhaust out. When the timing belt breaks the bottom of the engine keeps turning but the cam stops. Half of the valves will be in the down position or open. The pistons hit the valves and extreme damage occurs. I wanted to see what a damaged engine looked like so the people at ASAP Motors dismantled an engine that had been damaged and allowed me to see the cylinders. If I learned one thing, replace the timing belt when the time comes.

After you receive the estimate from your garage, do your homework. Shop the internet for what you are looking for. There are many suppliers who will compete against each other trying to offer the best deal. After you settle on whom you want to do business with, check out the BBB report. They are a very good honest source of information about companies. Then take and compare the prices you’re found with the installer you are using. An import reason to keep in mind is if the installer supplies the engine, he warranties the labor. But he will mark up the used engine he selling you and could be purchasing from the same company you are.

I , Fouzi owner FOUZIS SERVICE CENTER thank you for visiting , subscribe to my website I will be here to help you for more question or free quote. My Car Symptoms, is my new e-book subscribe now is  limited edition.
               

SUBSCRIBE for FREE News Letters And Our Month End Specials !!!!!

We are RMI and INSURANCE  ACCREDITED.


we do also gearboxes


 

SUBSCRIBE  NOW  we promise you do not share your email and information with anyone without your permission.

19/03/2011 Posted by | Uncategorized | , , , , , , , | Comments Off on Car Repairs Estimates

   

%d bloggers like this: